<FlowDocument xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation"
              xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml"
              xmlns:b="http://schemas.byk.com/2009/xaml/presentation"
			        Tag="Data Analysis">
  

  <Paragraph>This Test Report shows the measurement data of a <Bold>single test series</Bold> selected under 
             "List". The selection can be quickly changed in the List area on the left side. 
             The report contains two Tabs:
             </Paragraph>
  
  <Paragraph Style="{DynamicResource Header}">Data</Paragraph>
  
  <Paragraph>• The data table shows the numerical measurement values. The data in the rows and columns are 
               dependent on the instrument used for measurement:
               </Paragraph>
  
  <Paragraph><Bold>BYK-mac Data Table</Bold>  </Paragraph>
   
  <Paragraph>- Match to Std: Difference between checkzone and standard.
              </Paragraph>  
  
  <Paragraph>- Panel Match: Difference between two checkzones as defined in the organizer - Harmony check.
              </Paragraph>
  
  <Paragraph>Additional color and sparkle components can be displayed for BYK-mac data by setting the options in the 
              table header. For BYK-mac i also the Intensity Emission index can be activated.
              </Paragraph>
  
  <Paragraph><Bold>wave-scan and cloud-runner Data Table</Bold>  </Paragraph>
  
  <Paragraph>- Checkzone: Measurement data of each checkzone.
              </Paragraph> 
  
  <Paragraph>- Groups: Averages of a group as defined in the Organizer.
              </Paragraph>
  
   <Paragraph> </Paragraph>
  
  <Paragraph>• A <Bold>traffic light</Bold> status symbol is assigned to each checkzone, panel match or group.
               </Paragraph>       
            
  <Paragraph>• Values out of tolerance are highlighted in yellow or red according to the Pass/Fail definition 
               in the Standard Management modul.
               </Paragraph>
  
  
  <Paragraph Style="{DynamicResource Header}">Schematic</Paragraph>
  
  <Paragraph>• The <Bold>schematic</Bold> of the measured object as defined in the Organizer is displayed with
               traffic light symbols:       
               </Paragraph>
  <Paragraph>- "Single dots" for comparing checkzone to standard.
               </Paragraph> 
  <Paragraph>- "Double dots" for Panel Match comparison (BYK-mac).
               </Paragraph> 
  <Paragraph>- "Quadruple dots" for Group comparison (wave-scan, cloud-runner).
               </Paragraph> 
  
  <Paragraph>• Functions to change the Schematic size are available above the graphics.
               </Paragraph>       
  
  <Paragraph Style="{DynamicResource Header}">Charts</Paragraph>

  <Paragraph>• For uniformity analysis the measurement data of the checkzones are shown in a graph.
               The chart includes tolerance lines according to the specifications set in the 
               Standard Management.
               </Paragraph>
  
  <Paragraph><Bold>BYK-mac Chart</Bold>  </Paragraph>
  
  <Paragraph>• Buttons in the upper right corner allow to view the data as <Bold>Line, Travel</Bold> or 
               <Bold>Scatter</Bold> graph.
               </Paragraph> 
  
  <Paragraph>• Tabs in the lower area enable to display the color or effect difference data.
               </Paragraph> 
  
  
  <Paragraph><Bold>wave-scan Chart</Bold> </Paragraph>
  
  <Paragraph>• Buttons in the upper right corner allow to view the data as <Bold>Line</Bold> graph or as
               <Bold>Balance/Spectrum</Bold>. 
               </Paragraph> 
               
  <Paragraph>• The Balance Chart and Structure Spectrum are shown for horizontal
               and vertical checkzones separately.
               </Paragraph> 
  
  
  <Paragraph><Bold>cloud-runner Chart</Bold> </Paragraph>
  
  <Paragraph>• Buttons in the upper right corner allow to view the data as <Bold>Line</Bold> 
               graph or as <Bold>Mottling or Striping Chart</Bold>.
               </Paragraph>
               
  <Paragraph>• The Mottling and Striping Chart are shown for horizontal and vertical 
               checkzones separately.
               </Paragraph>
  
  
  <Paragraph Style="{DynamicResource Header}">Note:</Paragraph>
   
  <Paragraph>• To <Bold>zoom</Bold> parts of a graph, click on the desired area and drag the mouse to the right.
                </Paragraph>
                
  <Paragraph>• The <Bold>Print button</Bold> opens a dialog box for print out and configuration of its layout.
                </Paragraph>
  
  <Paragraph> </Paragraph>
  <Paragraph> </Paragraph>
   
</FlowDocument>